Dual Power Steering Pulley

[BusaDave9]

I am looking for a power steering pulley for 2 belts. I have checked eBay, Power Steering Pros Power Steering Box- Power Steering Rack - Power Steering Pros and AGR Performance-MB Motorsports
Does anyone have any ideas where I could find one?

 

[mylittlecj5]

Are you looking for the one like I have, that has 2 different size pulleys, or is there one that has 2 of the same size?

 

[BusaDave9]

I need 2 pulleys the same size.
I have a HP pump that also drives my hydraulic winch and it needs 2 belts. A lot of stock jeeps had 2 belts driving the PS pump. My fan and crankshaft pulley are for 2 belts.
My high output PS pump didn't come with a pulley.

 

[mylittlecj5]

I have a source that may have one. If I remember, I'll ask him this weekend.

 

[BusaDave9]

I have a source that may have one. If I remember, I'll ask him this weekend.

That would be fantastic. Thanks Mylittlecj5

 

[BusaDave9]

Here's what I need:

I found one for 95 fricking dollars here: Grand Wagoneer Parts: Steering
I was hoping to pay about one third that price. I can get a PS pump from many sources but they never come with a pulley.

 

[BusaDave9]

Actually the above pulley says it's for a FSJ. I am sending them an email asking if it would work for me.

 

[CJ007]

Here's one, Speed 8947 Chrome GM Power Steering Pulley 2 V-Belt .

It pretty, GM though, sorry don't know if that matters?

http://compare.ebay.com/like/280699902361?var=lv&ltyp=AllFixedPriceItemTypes&var=sbar&_lwgsi=y $19, not pretty

There are a few good threads using Google "dual power steering pully"

 

[BusaDave9]

The GM pulleys are easy to find but they fit on a 5/8 inch keyed shaft. It looks like my shaft is almost 3/4 inches and there is no key.

 

[CJ007]

Search Chrysler & Jeep Parts

A little cheaper, I searched part number from your post. 5018949AA

 

[BusaDave9]

Search Chrysler & Jeep Parts

A little cheaper, I searched part number from your post. 5018949AA

Great!
I love saving money.
:ty:
I tried calling them but I guess It's too late.

 

[IOPort51]

look something like this one??

 

[BusaDave9]

look something like this one??

Yes, It looks exactly like that one.

 

[IOPort51]

If you lived down the block I would hand it to you and tell you to bring the mount and pump back after you got it off,
If you can not find one Pm me with a shipping address and don't complain if it takes me a week or so to get it shipped.
How do you remove the pulley, by he way?

 

[Sasquach]

With a pulley puller of course , It grabs onto the raised lip on the pulley and pushes the shaft out.

 

[BusaDave9]

If you lived down the block I would hand it to you and tell you to bring the mount and pump back after you got it off,
If you can not find one Pm me with a shipping address and don't complain if it takes me a week or so to get it shipped.
How do you remove the pulley, by he way?

That would be fantastic Larry. I sent you a PM with my address. If you send me your email address or mailing address I can send you a check or PayPal.

 

[IOPort51]

so, what is the Allen hole in the front?? Sasquach I am guessing you have done this and have the T shirt so I will believe you, Dave you may end up with the whole pump.

With a pulley puller of course , It grabs onto the raised lip on the pulley and pushes the shaft out.

 

[mylittlecj5]

You can normally borrow a puller at your local parts house. Should be free to do so after deposit is refunded). It only takes a couple minutes to do.

 

[IOPort51]

and it looks like that puller??

 

[mylittlecj5]

something like that one. i have a kit I use, its similar to that one.