WARR-WAGON/ tow rig (Many pics - dialup beware)
-
Hello Guest, we are proud to now have our Wiki online that is completely compiled and written by our members. Feel free to browse our Jeep-CJ Wiki or click on any orange keyword when looking at posts in the forum.
WARR-WAGON/ tow rig (Many pics - dialup beware)
- Thread starter warrpath4x4
- Start date Start date:
- Last post Last post:
warrpath4x4
Jeeper
got what feels like quite a bit done today. found this little access door, there was one on each side. opened them up and cleaned out the dirt and stuff so they will drain water again. didnt see them till i was sitting eye level with it.
i got the new power steering pump pulley on, the new high pressure line, and the new pump on
it took a while to remember to how the pump mounted but i got it figured out. also had to modify the mounting brackets for the new alt. the 100 amp one is huge compared to stock.
clearance for new alt and new valve covers
had to bend the adjusting bracket
also had to bend the dipstick tube to clear the bottom of the new alt. used a brakeline tubing bender to bend the dipstick tube
also pulled the seat belts and the bench seat again so i can POR the floor boards and prep for the heater install
it kinda sucked being in the shop in 100+ degrees, dads truck said it was 110 sitting in the sun.
i got the new power steering pump pulley on, the new high pressure line, and the new pump on
it took a while to remember to how the pump mounted but i got it figured out. also had to modify the mounting brackets for the new alt. the 100 amp one is huge compared to stock.
clearance for new alt and new valve covers
had to bend the adjusting bracket
also had to bend the dipstick tube to clear the bottom of the new alt. used a brakeline tubing bender to bend the dipstick tube
also pulled the seat belts and the bench seat again so i can POR the floor boards and prep for the heater install
it kinda sucked being in the shop in 100+ degrees, dads truck said it was 110 sitting in the sun.
RunUOvr
Jeeper
- Posts
- 76
- Media
- 1
- Thanks
- 0
- Location
- Battle Mountain, Nevada
- Vehicle(s)
- 85 CJ7, 2005 dodge ram 2500, a few other toys
Tow rig? That thing needs a 12 valve. Just giving ya a hard time. Your truck is looking really good.
warrpath4x4
Jeeper
Cheepjeep85
Crazy Sr. Respected Jeeper
- Posts
- 4,934
- Media
- 57
- Thanks
- 0
- Location
- Chickamauga, Ga
- Vehicle(s)
- 1985 Jeep CJ7, 258, t-176, D300, AMC20, D30
updates? lookin good
warrpath4x4
Jeeper
updates, uh i still have it and its still not done lol. ive been tinkering with it here and there, ive had a couple of medical situations in the family here recently. also some of us have been starting a 4x4 club for the area.
onto what you wanna see
a couple of teaser shots
heres the dash setup so far, i still have work to do on it and its just sitting in there but heres my start.
also started on some cheap hood vents, i placed them towards the rear and outside edges so if it gets rain in it, it will be at the back of the wheel wells.
heres the vent material
like i said cheap hood vents, both sides cost me about $5 got them from home depot
measured and marked
cutcut and cleaned. i left the supports in the hood
i need to get some differnt bolts to attach it and then paint it
i should have this side done tomorrow night, i need bolts and more cut off wheels so i can cut the other side.
onto what you wanna see
a couple of teaser shots
heres the dash setup so far, i still have work to do on it and its just sitting in there but heres my start.
also started on some cheap hood vents, i placed them towards the rear and outside edges so if it gets rain in it, it will be at the back of the wheel wells.
heres the vent material
like i said cheap hood vents, both sides cost me about $5 got them from home depot
measured and marked
cutcut and cleaned. i left the supports in the hood
i need to get some differnt bolts to attach it and then paint it
i should have this side done tomorrow night, i need bolts and more cut off wheels so i can cut the other side.
warrpath4x4
Jeeper
today i got the other hole cut in the hood for the hood vents, got them put in most of the way, i need more hardware. apparently someone mixed a bunch of different thread pitch nuts in the bin at ace hardware so im short a few. the empty holes are waiting for more hardware.
then i had fun doing this by myself
if it wasnt for this truck being my tow rig when im done, i would just be building an "allpro style" bed and run it.
then i had fun doing this by myself
if it wasnt for this truck being my tow rig when im done, i would just be building an "allpro style" bed and run it.
warrpath4x4
Jeeper
CJ
Admin
- Posts
- 26,067
- Featured
- 3
- Media
- 881
- Resources
- 193
- Solutions
- 60
- Thanks
- 1,058
- Location
- Central FL
- Vehicle(s)
- '72 CJ5, 401, T18, D20, D44, D30
'82 CJ8, 258, D300, AMC20, D30
I think the hood vents are great! Novel idea! I also like the dash. Simple and functional... 
CoreyYoungCj577
Senior Jeeper
- Posts
- 999
- Media
- 18
- Thanks
- 0
- Location
- Billings,MT
- Vehicle(s)
- 1977 cj7 232 inline 6,Dana 20 Tc,T-150 Trans, stock diffs.
You know i have never been a fan of Dodge Power Wagons, But yours changed my outlook on them, looks like the build is coming along great!
warrpath4x4
Jeeper
warrpath4x4
Jeeper
cleaned the frame up some with a wire wheel
threw some black spray paint down
for now i welded the holes up that were drilled in the WARN winch bumper and threw some spray paint on it also. the jack stand is there because i need the right bolts for it, i just put a couple smaller ones in to hold it. after its all up and running i am going to build a bumper for it.
i also trimmed the fenders and found some bondo in the driver side fender. heres a comaprison from the uncut driver side to the cut passenger one, i need to clean up the cuts these are just rough cut out with the plasma.
threw some black spray paint down
for now i welded the holes up that were drilled in the WARN winch bumper and threw some spray paint on it also. the jack stand is there because i need the right bolts for it, i just put a couple smaller ones in to hold it. after its all up and running i am going to build a bumper for it.
i also trimmed the fenders and found some bondo in the driver side fender. heres a comaprison from the uncut driver side to the cut passenger one, i need to clean up the cuts these are just rough cut out with the plasma.
Similar threads
-
Question
Reply's are voted
on for best answer