dana 44 disc brakes
rr41mag
Full Time Jeeper
- Posts
- 2,015
- Thanks
- 2
- Location
- Panama city florida
- Vehicle(s)
- 04 dodge truck, 1966 chevy truck, 2012 rav4
And finally a 1981 jeep cj7 258 hardtop
Anyone done this conversion?
-
Hello Guest, we are proud to now have our Wiki online that is completely compiled and written by our members. Feel free to browse our Jeep-CJ Wiki or click on any orange keyword when looking at posts in the forum.
dana 44 disc brakes
- Thread starter rr41mag
- Start date Start date:
- Last post Last post:
IOPort51
NOT the voice of reason Jeep-CJ.com
- Posts
- 13,956
- Featured
- 5
- Media
- 458
- Thanks
- 15
- Location
- Garland Texas
- Vehicle(s)
- 1977 cj-5
4.2 W/MC2100 carb, 4.0 head W/3 angle valves,SS Header,TFI ignition with MSB-6 offroad module,CS144 140 amp RPS alternator with remote regulator T-150,d-20,Dana 44 with OX lock and disk brakes. D-30 with Spartin locker,
skyjacker 2.5 lift?nitro shocks,31" BFG A/T off road.8000 lb Warn winch, original owner.=^)
2006 Toyota Tacoma
Kane
Full Time Jeeper
- Posts
- 2,795
- Media
- 4
- Thanks
- 2
- Location
- Berlin, CT
- Vehicle(s)
- 1984 CJ-8 Restomod Scout axles 4 wheel disks, 258, ax15, D300.
I am doing it now. 1998 Suzuki Sidekick rotors 22mm thick and 1987 Nissan 300ZX calipers with built in ebrake. I bought the rotors from Advance Auto for $27 each and the calipers from an E-bay store for $50 each. I have to make my own caliper bracket that I plan to get water jetted after the design is finished. Also the ebrake cable needs a small bracket welded to the axle tube. The residual valve needs to be changed out to a 2lb from the existing 10lb. Otherwsie that is it.
rr41mag
Full Time Jeeper
- Posts
- 2,015
- Thanks
- 2
- Location
- Panama city florida
- Vehicle(s)
- 04 dodge truck, 1966 chevy truck, 2012 rav4
And finally a 1981 jeep cj7 258 hardtop
Kane
Full Time Jeeper
- Posts
- 2,795
- Media
- 4
- Thanks
- 2
- Location
- Berlin, CT
- Vehicle(s)
- 1984 CJ-8 Restomod Scout axles 4 wheel disks, 258, ax15, D300.
I am just going to attach the caliper to the rotor and then create a caliper bracket out of cardboard. Once I get that then I plan to transfer the design to a CAD drawing and have a local metal shop water jet them. I am not quite at that stage of the rear end build because I am still setting up the gears but I should be there in about a week. If I get a design I am happy with I may have the metal shop cut out a few extra sets so I can sell them. I will let you know if you are interested in a pair.
Last edited:
johnnyreb
Old Time Jeeper
- Posts
- 1,470
- Media
- 17
- Thanks
- 1
- Location
- tn
- Vehicle(s)
- 1980 cj5 258ci straight 6, 31x10.50's. Partial Teamrush iginition upgrade, MC 2150 Carb. 4.0 head swap, factory header. I call him "Eugene".
Dad's jeep when he raced in the 70's. Cj2 running gear, ford 300 cu in 6 cyl with 3 deuces. Fiberglass model T body and hand laid fiberglass hood. welded 5.38 gears and beer keg fuel tank. see avatar
Wife's: Black 04' Liberty with all the bells and whistles.
Similar threads
-
Question
Reply's are voted
on for best answer
TCase
Dana 20
-
Question
Reply's are voted
on for best answer
Misc
wheel question
-
Question
Reply's are voted
on for best answer
-
Question
Reply's are voted
on for best answer
