Jimbos YJ/CJ build
Jimbos76cj
Full Time Jeeper
- Posts
- 2,223
- Thanks
- 0
- Location
- St.Cloud FL
- Vehicle(s)
- 83 CJ-7.. 4" YJ springs front rear, J-10 44 front/AMC 20 rear,6 cy auto dana 300 35' bfg Done and gone!!
Ask me about my head light upgrade harness!!!
Got a call back from the powder coater about the dash today.. to blast it, lay down a high zince rust inhibiting primer and gloss black textured finish... $100. Sold! Inbetween down pours today I snuck into the shop and worked on the wiring a little more. Heres what Ive got done
I was able to run the new wires through the stock harness hoops. I measured and cut all the end to the right length and got em hooked up.
![IMG_4642_zpsf9a0ff8d.jpg IMG_4642_zpsf9a0ff8d.jpg](https://jeep-cj.com/community/data/attachments/56/56143-14fc3b994b3e95a5d1b03c09714a8d67.jpg)
Then I Ran some loom just for
s and giggles.. I still need to add the power wire for the fan realy into the loom. The green and tan wires are the head light and high beam leads that Ill use to power the relays. I wired in the choke realy and got it powered up.
![IMG_4643_zpsc98b4571.jpg IMG_4643_zpsc98b4571.jpg](https://jeep-cj.com/community/data/attachments/56/56144-a13947d926e4aee958804fb4c3766bc4.jpg)
Heres the drivers side.. the blinkers and markers will come in from this side.
![IMG_4644_zpsc7900367.jpg IMG_4644_zpsc7900367.jpg](https://jeep-cj.com/community/data/attachments/56/56145-a6cf77ec1ecb04f1a709eaa0aa528585.jpg)
and before the flaming starts I still need to make the cover for the hole where the old panel was.
Heres the "new" seats from Keith
![IMG_4640_zps85bc8f1a.jpg IMG_4640_zps85bc8f1a.jpg](https://jeep-cj.com/community/data/attachments/56/56146-9bf883b70d4d5a85310b5c61a2b25813.jpg)
and fancy soft door from Brian.
![IMG_4639_zps64409453.jpg IMG_4639_zps64409453.jpg](https://jeep-cj.com/community/data/attachments/56/56147-c74a084d0d89de1e1a8d0f655d2ebdb1.jpg)
Little bits I guess.
I was able to run the new wires through the stock harness hoops. I measured and cut all the end to the right length and got em hooked up.
![IMG_4642_zpsf9a0ff8d.jpg IMG_4642_zpsf9a0ff8d.jpg](https://jeep-cj.com/community/data/attachments/56/56143-14fc3b994b3e95a5d1b03c09714a8d67.jpg)
Then I Ran some loom just for
![Dung :dung: :dung:](/community/smilies/dung.gif)
![IMG_4643_zpsc98b4571.jpg IMG_4643_zpsc98b4571.jpg](https://jeep-cj.com/community/data/attachments/56/56144-a13947d926e4aee958804fb4c3766bc4.jpg)
Heres the drivers side.. the blinkers and markers will come in from this side.
![IMG_4644_zpsc7900367.jpg IMG_4644_zpsc7900367.jpg](https://jeep-cj.com/community/data/attachments/56/56145-a6cf77ec1ecb04f1a709eaa0aa528585.jpg)
and before the flaming starts I still need to make the cover for the hole where the old panel was.
Heres the "new" seats from Keith
![IMG_4640_zps85bc8f1a.jpg IMG_4640_zps85bc8f1a.jpg](https://jeep-cj.com/community/data/attachments/56/56146-9bf883b70d4d5a85310b5c61a2b25813.jpg)
and fancy soft door from Brian.
![IMG_4639_zps64409453.jpg IMG_4639_zps64409453.jpg](https://jeep-cj.com/community/data/attachments/56/56147-c74a084d0d89de1e1a8d0f655d2ebdb1.jpg)
Little bits I guess.