Quick! Buy lottery tickets!
DaveMueller
Active Jeeper
- Posts
- 272
- Media
- 1
- Thanks
- 7
- Location
- Ohiopyle, PA
- Vehicle(s)
- '76 CJ5 with an '88 258 from a YJ.
AMC20, D30, D20, T150.
I got my original fuel gauge working!
-
Hello Guest, we are proud to now have our Wiki online that is completely compiled and written by our members. Feel free to browse our Jeep-CJ Wiki or click on any orange keyword when looking at posts in the forum.
Quick! Buy lottery tickets!
- Thread starter DaveMueller
- Start date Start date:
- Last post Last post:
Torxhead
Always Off-Roading Jeeper
And just how did you manage that? I have been tweaking my fuel/temp gauge for years.
- Posts
- 12,365
- Featured
- 3
- Media
- 71
- Resources
- 2
- Thanks
- 278
- Location
- Rockwall,TX
- Vehicle(s)
- 1983 cj7, 1971 Dart, 1942 Willys slat grill
Dang son get you some tickets
Sent from past using Tapatalk
Sent from past using Tapatalk
DaveMueller
Active Jeeper
- Posts
- 272
- Media
- 1
- Thanks
- 7
- Location
- Ohiopyle, PA
- Vehicle(s)
- '76 CJ5 with an '88 258 from a YJ.
AMC20, D30, D20, T150.
Half luck/half skill?
I think it was mostly sloppy wiring by a PO. Luckily, it didn't work at all instead of shorting to ground and killing the meter. Bare corroded wire wrapped around the sender post, and grounded to a body mount bolt (I didn't know rubber was a conductor).
I replaced the ground wire and put it under a bolt on the skid plate, and replaced the wire from the sender through the floor to the harness.
I had to drop the tank to fix a leak, so I pulled the pickup/sender assembly to check it. The tank and sender don't look 40+ years old, but the mud collected at one small spot between the tank and skid plate and made a tiny hole. While I had the sender out, I pried off the cover and bent a little more tension on the wiper, figuring it didn't work anyways so I couldn't make it worse.
I put a few gallons in the tank and it didn't register so I thought the meter was dead. This morning I filled up on the way to work and noticed when I pulled out that the gauge was almost full.
I think it was mostly sloppy wiring by a PO. Luckily, it didn't work at all instead of shorting to ground and killing the meter. Bare corroded wire wrapped around the sender post, and grounded to a body mount bolt (I didn't know rubber was a conductor).
I replaced the ground wire and put it under a bolt on the skid plate, and replaced the wire from the sender through the floor to the harness.
I had to drop the tank to fix a leak, so I pulled the pickup/sender assembly to check it. The tank and sender don't look 40+ years old, but the mud collected at one small spot between the tank and skid plate and made a tiny hole. While I had the sender out, I pried off the cover and bent a little more tension on the wiper, figuring it didn't work anyways so I couldn't make it worse.
I put a few gallons in the tank and it didn't register so I thought the meter was dead. This morning I filled up on the way to work and noticed when I pulled out that the gauge was almost full.
Idahododgeram
Jeeper
I think I got mine working yesterday. I'm so glad I cut a hole in the tub over the sender so I could check the sender without dropping the tank. Maybe it's lottery tickets for both of us.
I now have all gauges working and I have turn signals too. Yipeeee!https://www.jeep-cj.com/forums/images/smilies/beerchug.gif
I now have all gauges working and I have turn signals too. Yipeeee!https://www.jeep-cj.com/forums/images/smilies/beerchug.gif
Similar threads
-
Question
Reply's are voted
on for best answer
