Identifying gear ration
- Posts
- 729
- Media
- 10
- Thanks
- 75
- Location
- West Springfield, MA
- Vehicle(s)
- 1986 CJ7, SBC 350, Dana 300, D30, AMC20
-
Hello Guest, we are proud to now have our Wiki online that is completely compiled and written by our members. Feel free to browse our Jeep-CJ Wiki or click on any orange keyword when looking at posts in the forum.
Identifying gear ration
- Thread starter Masscj7
- Start date Start date:
- Last post Last post:
RiverandSand
Senior Jeeper
- Posts
- 14,791
- Thanks
- 55
- Location
- Springfield, Missouri-U.S.A. Earth
- Vehicle(s)
- '85 CJ-7, 258/4.2L 6cyl. Bought new in 1985. Full cage, Warn 8274 winch, Ford 9" rear, front/rear Detroit Lockers w/4:88 R&P. T-5 tranny and 4:1 t'case. 33X12.50-15 BFG/AT, MSD ign, on board air---
IF it's still the OEM ratio-Most likly 2:73 or 3:31.
Pull the diff cover-The ring gear will have it stamped on it.
You sure your rear axle is not a '44'? Many '86s were.
LG
Pull the diff cover-The ring gear will have it stamped on it.
You sure your rear axle is not a '44'? Many '86s were.
LG
- Posts
- 11,552
- Media
- 57
- Thanks
- 11
- Location
- Frederick colorado
- Vehicle(s)
- 84 cj7, 91 cherokee, 78 chevy 3500 pu, 78 CJ7
He was talking about the front.
- Posts
- 729
- Media
- 10
- Thanks
- 75
- Location
- West Springfield, MA
- Vehicle(s)
- 1986 CJ7, SBC 350, Dana 300, D30, AMC20
Lumpy, I wish I had a 44, but unfortunately I have a 20.
But was talking about the front. I did find these markings on it this evening.
Sent from my iPhone using Tapatalk
But was talking about the front. I did find these markings on it this evening.
Sent from my iPhone using Tapatalk
coldair
Full Time Jeeper
Lumpy, I wish I had a 44, but unfortunately I have a 20.
But was talking about the front. I did find these markings on it this evening.
Sent from my iPhone using Tapatalk
Your Jeep has 2.73 gears
jp360cj
Old Time Jeeper
- Posts
- 1,119
- Thanks
- 1
- Location
- NC
- Vehicle(s)
- '77 CJ7, 360, 6.32 T18, D20, Narrowed Chevy D44 front, 9" rear
Yep, 49/18= 2.72s
When doing the tire to driveshaft rotation on an open diff, you need to make sure both tires are turning at the same speed. Best way is to roll the tires across the ground. If only 1 tire (or axle shaft) turns, you need to do 2 complete tire rotations. I learned that the hard way after a buddy passed up what turned out to be 3.54 WT axles because we couldn't figure out the ratio
Sent from my iPhone using Tapatalk
When doing the tire to driveshaft rotation on an open diff, you need to make sure both tires are turning at the same speed. Best way is to roll the tires across the ground. If only 1 tire (or axle shaft) turns, you need to do 2 complete tire rotations. I learned that the hard way after a buddy passed up what turned out to be 3.54 WT axles because we couldn't figure out the ratio
Sent from my iPhone using Tapatalk
- Posts
- 14,791
- Thanks
- 55
- Location
- Springfield, Missouri-U.S.A. Earth
- Vehicle(s)
- '85 CJ-7, 258/4.2L 6cyl. Bought new in 1985. Full cage, Warn 8274 winch, Ford 9" rear, front/rear Detroit Lockers w/4:88 R&P. T-5 tranny and 4:1 t'case. 33X12.50-15 BFG/AT, MSD ign, on board air---
2:73 ratio.Copy on the '20'-I have seen many who 'thought' they had a '20', when in fact it was a '44'..........
LG