Build Thread 1975 CJ6 on the skinny...
danc9
Active Jeeper
- Posts
- 475
- Thanks
- 0
- Location
- Clarksville, IN
- Vehicle(s)
- 1975 CJ 6, 258 I6, T-14, Dana 20, Dana 30, Dana 44
-
Hello Guest, we are proud to now have our Wiki online that is completely compiled and written by our members. Feel free to browse our Jeep-CJ Wiki or click on any orange keyword when looking at posts in the forum.
Build Thread 1975 CJ6 on the skinny...
- Thread starter danc9
- Start date Start date:
- Last post Last post:
BC CJ
Active Jeeper
- Posts
- 478
- Thanks
- 0
- Location
- British Columbia
- Vehicle(s)
- Early 1975 CJ 5
304, NP435, AA, D300, D30, D44
Re: 24 April 2012
Dang, you've got skills man.
Those pieces are comming out looking new! I cant wait to see this Jeep put back together. Great work.
Dang, you've got skills man.
Those pieces are comming out looking new! I cant wait to see this Jeep put back together. Great work.
danc9
Active Jeeper
- Posts
- 475
- Thanks
- 0
- Location
- Clarksville, IN
- Vehicle(s)
- 1975 CJ 6, 258 I6, T-14, Dana 20, Dana 30, Dana 44
26 April 2012
Wire wheeled the drivers side this morning. It is far worse than the passengers side for sure. Got the rear quarter done......
Till next time, DAN
Wire wheeled the drivers side this morning. It is far worse than the passengers side for sure. Got the rear quarter done......
Till next time, DAN
danc9
Active Jeeper
- Posts
- 475
- Thanks
- 0
- Location
- Clarksville, IN
- Vehicle(s)
- 1975 CJ 6, 258 I6, T-14, Dana 20, Dana 30, Dana 44
danc9
Active Jeeper
- Posts
- 475
- Thanks
- 0
- Location
- Clarksville, IN
- Vehicle(s)
- 1975 CJ 6, 258 I6, T-14, Dana 20, Dana 30, Dana 44
2 May 2012
I ordered the gasket set for the exhaust this morning. Bolted on the rear cross member on the frame and got it wire wheeled and primed. The rear support for the bed got welded in. That got primed and I got a little seam seal spread out.
good day!
Hope to get the exhaust started tomorrow. Maybe some top coat on the bottom of the tub!!!!!!
I ordered the gasket set for the exhaust this morning. Bolted on the rear cross member on the frame and got it wire wheeled and primed. The rear support for the bed got welded in. That got primed and I got a little seam seal spread out.
good day!
Hope to get the exhaust started tomorrow. Maybe some top coat on the bottom of the tub!!!!!!
DAN
danc9
Active Jeeper
- Posts
- 475
- Thanks
- 0
- Location
- Clarksville, IN
- Vehicle(s)
- 1975 CJ 6, 258 I6, T-14, Dana 20, Dana 30, Dana 44
3 May 2012
Wire wheeled the easy stuff on the back of the frame. Got that primed. Flipped up the tub and got the bottom painted with Rust-Oleum! Same brand of primer that I'm using. Had a little paint left so I painted the bottom of the front fenders as well......
Need to go pick up my manifold gaskets!
DAN
Wire wheeled the easy stuff on the back of the frame. Got that primed. Flipped up the tub and got the bottom painted with Rust-Oleum! Same brand of primer that I'm using. Had a little paint left so I painted the bottom of the front fenders as well......
Need to go pick up my manifold gaskets!
DAN
Last edited:
What did you paint the underside with?
danc9
Active Jeeper
- Posts
- 475
- Thanks
- 0
- Location
- Clarksville, IN
- Vehicle(s)
- 1975 CJ 6, 258 I6, T-14, Dana 20, Dana 30, Dana 44
Rust-Oleum
Rust-Oleum
Rust-Oleum
danc9
Active Jeeper
- Posts
- 475
- Thanks
- 0
- Location
- Clarksville, IN
- Vehicle(s)
- 1975 CJ 6, 258 I6, T-14, Dana 20, Dana 30, Dana 44
4 May 2012
Got the manifolds bolted back on. Picked up a muffler and got that bolted on....
DAN
Got the manifolds bolted back on. Picked up a muffler and got that bolted on....
DAN
IOPort51
NOT the voice of reason Jeep-CJ.com
- Posts
- 13,956
- Featured
- 5
- Media
- 458
- Thanks
- 15
- Location
- Garland Texas
- Vehicle(s)
- 1977 cj-5
4.2 W/MC2100 carb, 4.0 head W/3 angle valves,SS Header,TFI ignition with MSB-6 offroad module,CS144 140 amp RPS alternator with remote regulator T-150,d-20,Dana 44 with OX lock and disk brakes. D-30 with Spartin locker,
skyjacker 2.5 lift?nitro shocks,31" BFG A/T off road.8000 lb Warn winch, original owner.=^)
2006 Toyota Tacoma
outstanding body work!! impressive to say the least.
that is a heck of a bumper, the bolt holding it on is a bit underwhelming.
the exhaust pipe in front of the tire like that, would make me more than a little nervous.
that is a heck of a bumper, the bolt holding it on is a bit underwhelming.
the exhaust pipe in front of the tire like that, would make me more than a little nervous.
CJ
Admin
- Posts
- 26,259
- Featured
- 3
- Media
- 881
- Resources
- 193
- Solutions
- 59
- Thanks
- 1,082
- Location
- Central FL
- Vehicle(s)
- '72 CJ5, 401, T18, D20, D44, D30
'82 CJ8, 258, D300, AMC20, D30
Re: 26 April 2012
What did you use to roll out this patch panel? I fits nicely...
What did you use to roll out this patch panel? I fits nicely...
Wire wheeled the drivers side this morning. It is far worse than the passengers side for sure. Got the rear quarter done......
Till next time, DAN
danc9
Active Jeeper
- Posts
- 475
- Thanks
- 0
- Location
- Clarksville, IN
- Vehicle(s)
- 1975 CJ 6, 258 I6, T-14, Dana 20, Dana 30, Dana 44
A hammer.
The previous questions; The exhaust is temp, so when I bench test the engine the neighbors don't freak. It will be to the rear bumper when finished. The front bumper when finished will have six hardened bolts holding it on. I'd rather not undo that many bolts when fitting a fabricated piece.
DAN
The previous questions; The exhaust is temp, so when I bench test the engine the neighbors don't freak. It will be to the rear bumper when finished. The front bumper when finished will have six hardened bolts holding it on. I'd rather not undo that many bolts when fitting a fabricated piece.
DAN
Last edited:
Similar threads
Build Thread
Starting from the frame 1977 CJ5
Build Thread
1986 CJ-7 Laredo ALL NEW but the sheet metal...
