Installing used gears?
-
Hello Guest, we are proud to now have our Wiki online that is completely compiled and written by our members. Feel free to browse our Jeep-CJ Wiki or click on any orange keyword when looking at posts in the forum.
Installing used gears?
- Thread starter coldair
- Start date Start date:
- Last post Last post:
Torxhead
Always Off-Roading Jeeper
If its in a Jeep, its O.K.
CJ007
Old Time Jeeper
- Posts
- 1,351
- Media
- 75
- Thanks
- 0
- Location
- Peoria, AZ
- Vehicle(s)
- 83' CJ7-35's, granny T18, clocked, locked, 456s, D30 20 trussed- stitched-heim traction-1 piece shafts, CV dshaft, quick discos, xtended shock mounts, SOA, revolvers rear, braided lines, herculined, hand throttle, AMC saddle bags, rebuilt 258, D300.
I did rear used and no issues as of yet. Just gave a good look for wearing, chipping and cracks. I also went this way as it was my first attempt at gearing and figured I would rather ruin a cheap set if I screwed up 
I chipped stock gears on lesser trails than I do now so they have worked well.
I chipped stock gears on lesser trails than I do now so they have worked well.
- Posts
- 5,829
- Media
- 186
- Resources
- 1
- Thanks
- 74
- Location
- Plumas Lake, CA, USA
- Vehicle(s)
- 1974 CJ5 ~ Fresh built AMC 360 - SM420 - D20 - D30F with upgraded 30 spline shafts and knuckles & D44R - 4.27 Gears - ARB Lockers F/R - All chrome molly axles - on 33's - YJ 4" Lift Spring Conversion
Old Dog
Always Off-Roading Jeeper
- Posts
- 13,880
- Media
- 82
- Thanks
- 6
- Location
- Stonelick Lake, Ohio
- Vehicle(s)
- 83 CJ7 350 tbi, TH350, D300 twin sticked & clocked, narrowed Chief D44 Eaton Elocker & Moser shafts, Explorer 8.8 Detroit locker, 410's, RE 4.5" spring lift 1" body lift, 35" Claws, cage tied to frame, Corbeau baja seats, HD tie rod and draglink, u-bolts flipped, custom skid plate and sliders, Warn 9.5ti winch with Amsteel synthetic line
I'm running used gears in the rear of mine now and will be using used gears in the front when I change to the 44. I don't have a problem with used but not abused..
As for price I think anything less than half price. I see prices around $75 - 100 alot of times. If you know they have good bearings on them than they would be worth more.
As for price I think anything less than half price. I see prices around $75 - 100 alot of times. If you know they have good bearings on them than they would be worth more.
Last edited:
coldair
Full Time Jeeper
Anything cheaper than new...
~ JR
JR to bad you didnt say that a few hours ago payed 3 times the price of new ones lol I'm joking
- Posts
- 5,829
- Media
- 186
- Resources
- 1
- Thanks
- 74
- Location
- Plumas Lake, CA, USA
- Vehicle(s)
- 1974 CJ5 ~ Fresh built AMC 360 - SM420 - D20 - D30F with upgraded 30 spline shafts and knuckles & D44R - 4.27 Gears - ARB Lockers F/R - All chrome molly axles - on 33's - YJ 4" Lift Spring Conversion
JR to bad you didnt say that a few hours ago payed 3 times the price of new ones lol I'm joking
Sorry man! If only I wouldn't have had lunch with the lady today I could have seen this sooner and saved you the cash!
~ JR
73CJ
Crazy Sr. Respected Jeeper
- Posts
- 3,533
- Media
- 57
- Thanks
- 10
- Location
- Detroit Lakes, MN
- Vehicle(s)
- 73 CJ5 4.0 head on a 258, HEI, Holley Projection w/ 4.56, Detroit lockers Narrowed D44 front and full float D44 rear T14 w/ D20 4 wheel discs, 38.5 Boggers
Chances are you are going the wreck the bearings pulling them off to shim the pinion or carrier.
No chips or cracks is most important.
Incommando
Senior Jeeper
- Posts
- 945
- Thanks
- 1
- Location
- SW Ohio
- Vehicle(s)
- '77 CJ7 360/T18/D20 D60F/14bolt on 38's,
Stock '91 MJ 4.0/2wd parts runner
I just checked: everyone of my jeeps has used gears in it....
CJ
Admin
- Posts
- 24,584
- Featured
- 3
- Media
- 881
- Resources
- 193
- Solutions
- 52
- Thanks
- 928
- Location
- Central FL
- Vehicle(s)
- '72 CJ5, 401, T18, D20, D44, D30
'82 CJ8, 258, D300, AMC20, D30
You slay me!I just checked: everyone of my jeeps has used gears in it....
jasonmark1993
Old Time Jeeper
- Posts
- 1,366
- Media
- 10
- Thanks
- 2
- Location
- El Paso TX
- Vehicle(s)
- FJ cruiser (wifes ride)
2008 ZX10R,
73 CJ5, 408W, Toploader, Dana 20, 9" Dana 30 5.38 gears, next purchase=slicks
I ran used gears in a supercharged mustang and had no problem.
Its hard to get a decent pattern though. It'll just show up how they have been running. Sometimes you just have to look at the coast side.
Its hard to get a decent pattern though. It'll just show up how they have been running. Sometimes you just have to look at the coast side.
jasonmark1993
Old Time Jeeper
- Posts
- 1,366
- Media
- 10
- Thanks
- 2
- Location
- El Paso TX
- Vehicle(s)
- FJ cruiser (wifes ride)
2008 ZX10R,
73 CJ5, 408W, Toploader, Dana 20, 9" Dana 30 5.38 gears, next purchase=slicks
They did at first; only for about 50 miles though. My buddy gave them to me for free so I wasn't too worried about it. They quieted down to normal after that. I was always wondering about them but I beat the hell out of that car and never had a problem.
Similar threads
-
Question
Reply's are voted
on for best answer
Engine
Holley Sniper Install
-
Question
Reply's are voted
on for best answer
-
Question
Reply's are voted
on for best answer
Trans
Grinding gears
-
Question
Reply's are voted
on for best answer
-
Question
Reply's are voted
on for best answer
Trans
T15 shifter frozen up
