Clutch Clutch Linkage
Lou Tenant
Jeeper
79 CJ7 AMC 258 i6 / 4.2l three speed. I ordered the Crown kit. I attempted to mount it to the firewall and it is approximately 200````
4
4
-
Hello Guest, we are proud to now have our Wiki online that is completely compiled and written by our members. Feel free to browse our Jeep-CJ Wiki or click on any orange keyword when looking at posts in the forum.
Clutch Clutch Linkage
- Thread starter Lou Tenant
- Start date Start date:
- Last post Last post:
Lou Tenant
Jeeper
Thank
Last edited:
- Posts
- 505
- Featured
- 3
- Media
- 135
- Resources
- 2
- Solutions
- 2
- Thanks
- 268
- Location
- Colorado
- Vehicle(s)
- 1986 CJ7 Laredo:
258 w/Howell TBI, HEI Ign., Dana 44 Front w/Detroit, Dana 44 Rear w/Discs & Detroit,
NP435 Trans, Dana 300 T-case w/twin stick
1969 Bronco:
351W, D44 high pinon front from full size, 9” full size rear, NP435 trans and Dana 20
Do you have a body lift, by chance?
Can you post a picture of what you mean by “2 inches too short” ?
Can you post a picture of what you mean by “2 inches too short” ?
Lou Tenant
Jeeper
No body lift. I'm not sure i can get a picture where it's located. The bell crank in the new kit is shorter than the ome.
- Posts
- 505
- Featured
- 3
- Media
- 135
- Resources
- 2
- Solutions
- 2
- Thanks
- 268
- Location
- Colorado
- Vehicle(s)
- 1986 CJ7 Laredo:
258 w/Howell TBI, HEI Ign., Dana 44 Front w/Detroit, Dana 44 Rear w/Discs & Detroit,
NP435 Trans, Dana 300 T-case w/twin stick
1969 Bronco:
351W, D44 high pinon front from full size, 9” full size rear, NP435 trans and Dana 20
I’m not 100% sure, but I believe that bell crank was a bit shorter in early generation CJs, like up to ‘75.
Maybe you have one of those?
The original on my ‘86 is 9” +/- long.
Maybe you have one of those?
The original on my ‘86 is 9” +/- long.
TSB8C
Old Time Jeeper
- Posts
- 1,153
- Featured
- 11
- Media
- 26
- Resources
- 1
- Solutions
- 29
- Thanks
- 623
- Location
- Cut-n-Shoot, TX
- Vehicle(s)
- 1984 CJ7, 420 HP "ZZ6 EFI" Crate engine, 700R4, D300, Dana30 front, Dana489 rear, 4.56 gears, 4" lift
'76 and up used a different bell crank (OE part # 5360104).
The '72-'75 is shorter (OE part # 5351292).
At a glance without measuring you can also tell the difference between the two because the grease zerk fitting is in a different position relative to the "arm" on the one end as well.
And then the even older '66-'71 is a lot different (OE part # 941232).
The '72-'75 is shorter (OE part # 5351292).
At a glance without measuring you can also tell the difference between the two because the grease zerk fitting is in a different position relative to the "arm" on the one end as well.
And then the even older '66-'71 is a lot different (OE part # 941232).
- Posts
- 505
- Featured
- 3
- Media
- 135
- Resources
- 2
- Solutions
- 2
- Thanks
- 268
- Location
- Colorado
- Vehicle(s)
- 1986 CJ7 Laredo:
258 w/Howell TBI, HEI Ign., Dana 44 Front w/Detroit, Dana 44 Rear w/Discs & Detroit,
NP435 Trans, Dana 300 T-case w/twin stick
1969 Bronco:
351W, D44 high pinon front from full size, 9” full size rear, NP435 trans and Dana 20
TSB8C, you nailed it, as usual!
Similar threads
-
Question
Reply's are voted
on for best answer
-
Question
Reply's are voted
on for best answer
Clutch
TO bearing "play"
-
Question
Reply's are voted
on for best answer
-
Question
Reply's are voted
on for best answer
Clutch
Stubborn spring attachment
-
Question
Reply's are voted
on for best answer