Build Thread My 1971 CJ5 Build Thread
-
Hello Guest, we are proud to now have our Wiki online that is completely compiled and written by our members. Feel free to browse our Jeep-CJ Wiki or click on any orange keyword when looking at posts in the forum.
Build Thread My 1971 CJ5 Build Thread
- Thread starter hazzo1
- Start date Start date:
- Last post Last post:
hazzo1
Jeeper
Update:
Painting was put of until tomorrow. Instead, we assembled the front clip. I'll let the pictures speak for themselves.
Painting was put of until tomorrow. Instead, we assembled the front clip. I'll let the pictures speak for themselves.
hazzo1
Jeeper
Sorry. Double post.
Cheepjeep85
Crazy Sr. Respected Jeeper
- Posts
- 4,934
- Media
- 57
- Thanks
- 0
- Location
- Chickamauga, Ga
- Vehicle(s)
- 1985 Jeep CJ7, 258, t-176, D300, AMC20, D30
Lookin good man
Sent from my DROID2
Sent from my DROID2
hazzo1
Jeeper
UPDATE:
I'm super busy at work today....So I'll let the pictures speak for themselves. I also included some pictures of the rock sliders for jcarr.
I'm super busy at work today....So I'll let the pictures speak for themselves. I also included some pictures of the rock sliders for jcarr.
hazzo1
Jeeper
oldguy
Active Jeeper
That is one beautiful Jeep!
Dano12771
Jeeper
Love the headers. Powder coated?
CJ
Admin
- Posts
- 22,884
- Featured
- 5
- Media
- 897
- Resources
- 193
- Solutions
- 45
- Thanks
- 791
- Location
- Central FL
- Vehicle(s)
- '72 CJ5, 401, T18, D20, D44, D30
'82 CJ8, 258, D300, AMC20, D30
You cannot powder coat headers, they get too hot... Looks like ceramic to me.Love the headers. Powder coated?
BTW - Nice 71!
hazzo1
Jeeper
hazzo1
Jeeper
hazzo1
Jeeper
oldguy
Active Jeeper
As I've said before "beautiful Jeep". The bumpers, you made or aftermarket??
73CJ
Crazy Sr. Respected Jeeper
- Posts
- 3,533
- Media
- 57
- Thanks
- 10
- Location
- Detroit Lakes, MN
- Vehicle(s)
- 73 CJ5 4.0 head on a 258, HEI, Holley Projection w/ 4.56, Detroit lockers Narrowed D44 front and full float D44 rear T14 w/ D20 4 wheel discs, 38.5 Boggers
Nice headlights and buckets. Where did you find them? Brand?
Whole darn thing is nice!
Whole darn thing is nice!
BusaDave9
Always Off-Roading Jeeper
- Posts
- 8,248
- Featured
- 3
- Media
- 361
- Resources
- 2
- Thanks
- 88
- Location
- Durango, Crawlarado
- Vehicle(s)
- 1979 Jeep CJ5 with 304 V8, T18 Transmission, Dana 20 Transfer case with TeraLow 3:1 gears, 4.88 axle gears, Detroit Locker up front and Ox Locker in back with 1 piece axle shafts, 36" SuperSwamper SX Tires, Shackle reversal, MileMarker Hydraulic winch, MSD 6A ignition.
hazzo1
Jeeper
Thank you! My dad and I built the bumpers.
We didn't get the headlight bulbs installed until after I took all of these pictures....But the assemblies and buckets are original. Just cleaned up and a fresh coat of paint and clear.
Thank you!
rebel4x4
Jeeper
hazzo1
Jeeper
Just a small update today....
oldguy
Active Jeeper
It's been a while guy. Your killing me with the suspense!!
hazzo1
Jeeper
Sorry about that. haha
My dad has been traveling a lot recently and I have more fun when I'm working on the Jeep with him...ha
But here is a small update...
My dad and I pulled the Transmission and the Transfer Case out Saturday afternoon to fix a leak we had between the Transmission and the bell housing. We found the oil was weeping out of a pressed in plug on the front on the case. We used some silicone and a homemade gasket to try to correct it....We'll find out if it worked after we top off the Transmission with oil...
We discovered a water leak while we were getting the cooling system ready...There is a steady stream of water leaking from the driver's side water pump port behind the timing cover....Looks to have the wrong gasket installed....Woo...
I started to refinish the set of aluminum wheels we have, but I can't see myself restoring these wheels by hand...So I have a buffer pad set coming from Eastwood. Should make things much less tedious.
But good news is that we are getting very close to firing the engine. I can't wait to finally hear this thing run!