Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Hello Guest, we are proud to now have our Wiki online that is completely compiled and written by our members. Feel free to browse our Jeep-CJ Wiki or click on any orange keyword when looking at posts in the forum.
I have acquired a 1979 narrow track CJ7 . I want to do significant modification to this Jeep, beginning with replacing the axles with wider track Dana 44 's. I see that there are several shops on the web that can do custom work for me. Also, I know that many have gotten Dana 44 's from older vehicles and modified them. I don't know whether at the end of the day, it's cheaper to work with old axles or to just order what I want. Looking for those who have experience with this and possibly some suggestions as to what older vehicles might have the axles that would work. I am able to weld, cut steel, etc.
I too looked at whether to use axles from another vehicle or just get new from a shop. I decided to go with the Dana489 from East Coast Gear Supply to replace the rear AMC20 . Heavier duty, custom setup, disc brakes, 99% plug-and-play.
You’re gonna get a ton of info on this site, as a lot of us have done axle upgrades. The search function is great for this.
I’ve done axle upgrades on 2 CJs and helped my Father with his CJ as well.
1. 1979 CJ5 : '70s Ford 9" rear and '70s Scout II front Dana 44 .
2. 1986 CJ7 : '70s Scout II rear and '70s Wagoneer Dana 44 front (you can see the details for this in my build thread on this site).
3. 1976 CJ5 : '80s Ford F350 D60 high pinion in the rear and same D60 for the front.
The Dana 60s are quite a bit more work and will be harder/more expensive to obtain and build. Probably overkill for most people's purposes.
I'd lean towards the Dana 44 or Ford 9" personally. I priced up a front Dana 44 from the same East Coast Gear Co. and for my purpose it was about 50% cheaper to do it myself. Of course, it depends on the cost of the donor axle and mine were free. The front end will obviously cost more than the rear, regardless of d.i.y or just purchasing.
1970s Jeep Wagoneers/Cherokee/Chiefs/J-Trucks are common donors. Also, 1970s Scout II had 'em. These are the easiest route too if you're staying with spring under axle.
D44s were also in 1970s Chevy 1/2 & 3/4-ton trucks and I believe Dodge used 'em too in their trucks and Wagons, but I'm not too sure of the vintage range. However, the Chevy and Dodge have spring over axle and will complicate things a bit if you don't want that, because the spring perch is cast into the center diff housing.
The rear Dana 44 can be obtained from the 1970s Scout IIs or again the same vintage Wagoneers as above, excluding the QuadraTrac rears which do not have the pinion in the center. These are good candidates because the widths are just about right if you're going for a wider track around 60". I think Isuzu and Honda SUVs used the Dana 44 too in the 90s, but I don't know much about these guys.
Ford 9" are plentiful because they were used forever and they're a fairly easy swap into the rear of a CJ. Look for a 60s-70s 1/2-ton truck which have about the right wide track width of around 60".
I am still humming and hawing on my axle build eh Been told to go D 44, reinforced moser axles etc I have had a Performance Driveline shop spec me 9" Ford nodular axle set wide track . Built for overkill apocolypse. Steering much beefier... Combat vet eh alwals thinking ahead. Looked into ARB front diff 4.33 gears to match new 5spd and 33" tires for 50/50 trail/ highway. Deep breath now eh $10,000 me not supplying said axles, and not installed. Lol still a less expensive build than my 93 1st Gen W250 lifted for 40's Am laughing, but crying too eh
I went with ECGS for my Dana 44 , you can buy it as a bare housing or complete and they have a lot of options available for them. I bought the housing bare with axle shafts and disc brakes then did my own gear and locker setup. The cost ended up being about even up in the end, but i did get some practice doing differential work, if you dont have the tools and measuring equipment to set up the ring and pinion you would be better off to let them do the work and have a bolt in axle when its delivered, they come plumbed, geared, and ready to go from pallet to jeep in quick fashion.
