Build Thread $600 CJ5!
-
Hello Guest, we are proud to now have our Wiki online that is completely compiled and written by our members. Feel free to browse our Jeep-CJ Wiki or click on any orange keyword when looking at posts in the forum.
Build Thread $600 CJ5!
- Thread starter Tim_Coble
- Start date Start date:
- Last post Last post:
-
- Tags
- 304 cj5 frame restoration
CJ
Admin
- Posts
- 24,376
- Featured
- 3
- Media
- 881
- Resources
- 193
- Solutions
- 50
- Thanks
- 911
- Location
- Central FL
- Vehicle(s)
- '72 CJ5, 401, T18, D20, D44, D30
'82 CJ8, 258, D300, AMC20, D30
Rain is a good thang! So is corn, cotton and Jeeps! I'm from the South!
Finally completed the tear down! The spring bolts were basically welded in - it took a lot of pounding, cursing, and some fire to break them loose. Now, I can get to the rust removal and start rebuilding.
CJ
Admin
- Posts
- 24,376
- Featured
- 3
- Media
- 881
- Resources
- 193
- Solutions
- 50
- Thanks
- 911
- Location
- Central FL
- Vehicle(s)
- '72 CJ5, 401, T18, D20, D44, D30
'82 CJ8, 258, D300, AMC20, D30
Nice work. 
What are you going to do with that wonderful front bumper? 
What are you going to do with that wonderful front bumper? 
- Posts
- 6,652
- Featured
- 1
- Media
- 20
- Solutions
- 3
- Thanks
- 607
- Location
- New Orleans area
- Vehicle(s)
- 84 CJ7 4 banger-owned since new in 1984 bought off truck at dealership - rebuilding 258, T176 with Sniper EFI D300 4:1 Lomax gears Twin Sticked 1 piece axels with locker
Another weekend and a little more progress. I started tearing down the axles and it looks like I will be going the 1 piece upgrade route. The driver side didn't look too bad, but the passenger side spun at some point. I thought about just replacing the one side axle and hub but it's less than double to just upgrade both sides and be done with it.
So far I have only looked at the outer shafts on the front, not horrible but I will probably just go ahead and replace both with chrome moly and be done with it. Driver's side looks worse than the pass.
Both Warn manual hubs were locked up and full of dirt, those will get a replacement unless I can find a rebuild kit.
Need to get the spindles pulled and figure out what socket to use for the yoke on both front and rear.
Both Warn manual hubs were locked up and full of dirt, those will get a replacement unless I can find a rebuild kit.
Need to get the spindles pulled and figure out what socket to use for the yoke on both front and rear.
- Posts
- 6,652
- Featured
- 1
- Media
- 20
- Solutions
- 3
- Thanks
- 607
- Location
- New Orleans area
- Vehicle(s)
- 84 CJ7 4 banger-owned since new in 1984 bought off truck at dealership - rebuilding 258, T176 with Sniper EFI D300 4:1 Lomax gears Twin Sticked 1 piece axels with locker
Here’s my 41 1/2 year old front
axel u joints and spindle bearings from last week. 2 caps were done. Spindle bearings were good but replaced
axel u joints and spindle bearings from last week. 2 caps were done. Spindle bearings were good but replacedThose look like the ones that came out of my drive shafts. I'm pretty sure before mine was moved to the hill I picked it up on, it was sitting at the bottom of a drainage.
My driveshaft u-joints looked similar - lots of red. I'm pretty sure that before my jeep was parked on the hill I picked it up from it was at the bottom of a drainage. Everything has been full of dirt.
