Build Thread 83 CJ7 its time to get it done

[95yjman]

Looks good man!


Sent from my iPhone using Tapatalk

 

[Belizean]

Nice looking Transmission

 

[gert]

Nice looking Transmission

Can't wait to install it


Sent from my iPhone using Tapatalk

 

[gert]

Wow I weighed my old T-4 /T-5 bellhousing and it's only 8.8 pounds man that a lot a difference


Sent from my iPhone using Tapatalk

 

[gert]

1 down 3 to go, these will hold the 1.5 inch alignment bar centered in the axle when I go to narrow the rear

Sent from my iPhone using Tapatalk

 

[95yjman]

How much are you gonna narrow it?


Sent from my iPhone using Tapatalk

 

[gert]

How much are you gonna narrow it?


Sent from my iPhone using Tapatalk

from 67 inches down to 60 so 3.5 inches a side

 

[95yjman]

from 67 inches down to 60 so 3.5 inches a side

Cool, cool

 

[gert]

BAM......... Moser housing ends on the way, got both carrier locating pucks made time to party
http://www.moserengineering.com/catalogsearch/result/?q=7750db


Sent from my iPhone using Tapatalk

 

[daddyusmaximus]

Can't wait to see how they come out. I would be scared to do this myself. I hate how far the wheels and tires stick out with my CJ5 's full size Dodge truck axles. I want them narrowed, but I'll have to have it done professionally.

 

[gert]

Can't wait to see how they come out. I would be scared to do this myself. I hate how far the wheels and tires stick out with my CJ5 's full size Dodge truck axles. I want them narrowed, but I'll have to have it done professionally.

narrowing your axles are not the cheapest thing that we can do on a Jeep for sure, Im looking at have $700 in parts for the rear alone and an additional $1000 for the front

 

[gert]

When my housing ends show up Tuesday I can finish mill my housing end hockey pucks and narrow my rear axle

 

[gert]

I cant stand it I just have to get my 2600th post in

 

[Belizean]

I cant stand it I just have to get my 2600th post in

Congratulations Are those some type of special steel or hardened?

 

[gert]

Congratulations Are those some type of special steel or hardened?

Nope some scrap stainless that was being thrown away


Sent from my iPhone using Tapatalk

 

[gert]

I drilled my early housing to match my late model bell housing, trying to get the pilot bearing out so I can get the new bushing in.... the wife is at work so it's hard to get out to the garage, I hope to have the Transmission in the Jeep this weekend

Sent from my iPhone using Tapatalk

 

[gert]

Scooby snacks...... we are putting an over in on a new home :0 that means I have to get ours ready to sell by Wednesday..... I did however get the super pain in the butt old pilot bearing out and the new brass one installed and the clutch is back together waiting on me to install the Transmission now

Sent from my iPhone using Tapatalk

 

[gert]

Super monumental day for me...... the pig is in and the bell housing is a tight fit around the flywheel it makes me so happy to see my Transmission in place.

Sent from my iPhone using Tapatalk

 

[Petescj]

Super monumental day for me...... the pig is in and the bell housing is a tight fit around the flywheel it makes me so happy to see my Transmission in place.

Sent from my iPhone using Tapatalk

Awesome! Getting closer.

 

[shum8]

Super monumental day for me...... the pig is in and the bell housing is a tight fit around the flywheel it makes me so happy to see my Transmission in place.

Very nice, sir!

I wanna get mine back together so bad I'm gettin itchy..... in places I'd rather not have itch LOL.

Looks like you may be notching the Transmission tunnel for yer twin sticks, huh?